Normandy Beach Race

Normandy Beach Race Sept 26  on the Beach ,Belgium and French border.

 

TOY RUN

Annual Christmas Toy Run

Many Cars  get put away for the winter so this takes place in September.

Lot of smoke from Fires in Washington and Oregon so a bit uncomfortable.

Very difficult for the poor folks down South,Much damage!

Notice the smoke,that is not Sea Fog!

 

Bomber Seats

DONE!

Seats are comming together very well!

Getting the rivits done and the seat angle back a bit.

Spent a couple of days with Nick, Building Bomber seats. WE have a bead roller and he motorized it  with a foot control! So nice! Then Nick located a pickup box so we  put it on top of the ratty wood deck to see how it looked without shortening. We decided to leave it stock length just like some  young fellow would have done in 1950. He decided to go with the original length. I agree!

The seats will get some more beads but are going to look quite original. I took up some AN 470 rivets and we did some test riveting and with some of our old Aircraft  bucking bars  and rivet sets we will be OK

Tail gate is as good as any you would find these days

 

More paint on today

Now I have the new engine in the Hot Rod so back to the truck.

Sun Visor

Todays project. Sun Visor 
made from an old 49  1/2 ton hood,punched some holes and flared
Painted now back to the doors for more work.

Door repair for Pick up

Back to the truck project! 

Someone in the past used a chain around the door?  Only the RH side and mashed the upper part. I got a clapped out rusty door from Terry. Good doors are hard to find up here in the PNWEST, rain country!

So cut out the top and am fitting it in. Will close it up tomorow.

Then I will start doing locks and PWR windows.

High lite these photos for the complete picture size.

DONE! Took the day but am happy how it turned out. now onto something else.

Nice day for a drive

 Notice the red filler , That is my vent and oil filler . Hope it works as the Roof does not have any filler at the front and I do not have room at the old fuel pump area. I blanked it off and have a PCV  from it to the manifold.  

 Hot Rod runs fine! 

I am pleased with the PMG inside the 28 Ford Powerhouse generator case! Indicates about 20 amps and as I have an old curved glass SW  amp gauge that is 15 and 30 amp marks I am OK with that.

The Old Roof intake does not have exhaust heat but as soon as the block is warm all is well.

Doe not have the Jam of the old Flathead I took out but the lack of a knock is nice.

So after another retorque  which will be three and if no change then I call it done.

We took the 56 Chev out for an Ice Cream and sat on a small mountain  Mt Tolmie and looked over the city. About 25 C today,very nice.

I am not the speedball some people are! Any way today I made  a bracket for the coil cover.
Boght some spark plugs the other day. I took in  my Champion UD 16 and some Autolite B9 in and he matched them up as Autolite 386.
Look the same  when I look close and can not see any difference?
So there you go  old big thread  like original and only 34 Cdn $ for all  so I am happy.
Tomorrow is fuel lies and some wireing!

Engine out

Out it comes!
Been in there for about 35 years! Finally wore it out.

New old one going in.

BAD NEWS!!

I decided to take the HOT ROD for a drive a couple of weeks ago.
WE were heading off to Denmark for a couple of weeks and  it was a nice day so decided to go for a spin.
On the way back as I was driving in the driveway a nice loud KNOCK! started.
Rolled into the garage and walked away.

So a couple of weeks later now and

  it looks like the backup engine is going in.

I plan on some wiring changes  and the 28 Model A power house gen housing with  Kabota  PMG guts,good for about 25 amps 12 volt. That is all I need.

seems I am going backwards rather than forward!